Difference between revisions of "Fisheye/On Board Dewarping"
(Created page with "==How To Dewarp Fisheye On Board== ===Description=== A newer revision of firmware will enable your fisheye to dewarp onboard and then send the video stream to any device with...") |
(→Step by Step Instructions) |
||
| Line 13: | Line 13: | ||
1. Log into the camera and install the new WebRec plugin for this device. | 1. Log into the camera and install the new WebRec plugin for this device. | ||
| − | [[ | + | [[File:onboarddewarp009.jpg|500x500px]] |
2. Navigate to Setup->Image->Encode menu select the orientation of your mount under installation mode (Ceiling, Wall, Ground). | 2. Navigate to Setup->Image->Encode menu select the orientation of your mount under installation mode (Ceiling, Wall, Ground). | ||
| − | [[ | + | [[File:onboarddewarp011.jpg|500x500px]] |
3. Below are screenshots of how the record modes look: | 3. Below are screenshots of how the record modes look: | ||
| Line 23: | Line 23: | ||
*1O | *1O | ||
| − | [[ | + | [[File:onboarddewarp007.jpg|500x500px]] |
*1P | *1P | ||
| − | [[ | + | [[File:onboarddewarp008.jpg|500x500px]] |
*2P | *2P | ||
| − | [[ | + | [[File:onboarddewarp003.jpg|500x500px]] |
*1O+3R | *1O+3R | ||
| − | [[ | + | [[File:onboarddewarp001.jpg|500x500px]] |
*1R | *1R | ||
| − | [[ | + | [[File:onboarddewarp002.jpg|500x500px]] |
*4R | *4R | ||
| − | [[ | + | [[File:onboarddewarp005.jpg|500x500px]] |
*2R | *2R | ||
| − | [ | + | [File:onboarddewarp004.jpg|500x500px]] |
4. Now add the camera like a normal IP camera to your NVR, and notice that you can change every setting in the encode menu except the dewarp mode. The onboard dewarp setting must be configured directly through the camera's webGUI. | 4. Now add the camera like a normal IP camera to your NVR, and notice that you can change every setting in the encode menu except the dewarp mode. The onboard dewarp setting must be configured directly through the camera's webGUI. | ||
| − | [[ | + | [[File:onboarddewarp010.jpg|500x500px]] |
5. Here is an example of this feature being used on an NVR. | 5. Here is an example of this feature being used on an NVR. | ||
| − | [[ | + | [[File:onboarddewarp009.jpg|500x500px]] |
Revision as of 23:19, 2 December 2016
Contents
How To Dewarp Fisheye On Board
Description
A newer revision of firmware will enable your fisheye to dewarp onboard and then send the video stream to any device without post processing. This can be useful in video management environments that cannot dewarp these devices. Follow these instructions to find out how this function works.
Prerequisites
- Windows PC or Laptop
- Windows versions Vista, 7, 8 or 10
- DH-IPC-EBW812A0N(I) or DH-IPC-EBW86A0N(I) with dewarp firmware.
Video Instructions
Step by Step Instructions
1. Log into the camera and install the new WebRec plugin for this device.
2. Navigate to Setup->Image->Encode menu select the orientation of your mount under installation mode (Ceiling, Wall, Ground).
3. Below are screenshots of how the record modes look:
- 1O
- 1P
- 2P
- 1O+3R
- 1R
- 4R
- 2R
[File:onboarddewarp004.jpg|500x500px]]
4. Now add the camera like a normal IP camera to your NVR, and notice that you can change every setting in the encode menu except the dewarp mode. The onboard dewarp setting must be configured directly through the camera's webGUI.
5. Here is an example of this feature being used on an NVR.
